| | 
1970 JEEP CJ5 401 ALL NEW
|
 Ad ID: | #35040 | | Seller: | #12615 | | Expiry Date: | 8/21/2010 | | Location: | lancaster pa, Pennsylvania | | Price: | $17000 - US Dollars | | Ad Views: | 3561 |
|
|
|  |
 Description: | Engine
401 .030 over freshly rebuilt
ARP Rod Bolts
Speed Pro 9.8 to 1 Forged pistons
Moly Rings
Comp Cams Xtreme Energy XE262H cam .493/.500 lift.
Comp cams lifters and matched valve springs
8.5 Qt Bulltear oil pan zinc coated
High volume oil pump
Matched Dist. Gear and cam gear from Bulltear
New timing cover
Stainless oil midplate from Bull Tear
New Harmonic Balancer
Hardened Push Rods
Guide plates and screw in studs installed in heads along with any valves that needed replaced and all new seals and retainers/locks
Harland Sharp Roller Rockers
CFR Tall Aluminum valve covers
Hedman Elite ceramic long tube fenderwell headers.
Purple Hornie mufflers painted ceramic black
Edelbrock performer intake
Holley 660 Truck avenger carb
Edelbrock air filter
Carter Street rod fuel pump
Pre bent Stainless fuel line back to gas tank
MSD Pro billet dist.
MSD 6A ignition
MSD blaster 2 coil
Summit racing 100 amp black alternator with chrome pulley
MSD plug wires
Bulltear billet alternator bracket
Billet plug wire hold downs
Optima Red Top Battery
Stainless battery tray
Painless Pre terminated full wiring harness throughout jeep
IMI Mini torque starter
Dual electric fan with relay with automatic kick on/off
Flow Kooler Water Pump
3 Core Aluminum Radiator
Jeep Was Dyno Tuned at Bradys High Performance
Est. 410 horse and 505 ft/torque at motor
1977 frame
Frame was sand blasted, sprayed with epoxy primer and then painted with a urethane black.
Shackle hangers were gusseted and powder coated gray with new poly bushings installed.
New rear cross member installed with extra supports added.
Custom front bumper with stinger hoop and D ring mounts powder coated black.
Warn rear rock crawler bumper.
New gas tank skid plate.
Suspension
Heavy duty ½” lift shackles installed with boomerang style in the front.
All new poly bushings.
4” BDS Suspension kit with a 2” body lift installed.
New aftermarket U Bolt skid plates
Driveline
AMC 20 rear with rebuilt with new bearings and seals. 3.54 gears
Alloy 1 pc axles
Welded Diff. and also welded the axle tubes all the way around.
Installed heavy duty spring perches at the correct angle.
3/8” Diff. cover powder coated gray.
Tom Woods rear CV driveshaft and Tom Woods front driveshaft.
2 Inch Spider Traxx Wheel spacers front and back.
Dana 30 front rebuilt with all new seals and bearings. 3.54 gears
Loc Rite installed. New U joints installed in axles.
Converted to front disc brakes
5 bolt hubs with stud kit.
New rotors and brake pads.
BDS steering stabilizer.
Big Daddy Drag link kit.
Tie rod and Drag link flipped to top of steering knuckles
Steering knuckles were powder coated black.
Diff cover powder coated gray with black warn guard.
4” Rancho red bump stops
Red poly trans mount.
4 speed T18A trans with 6.32 to 1 1st gear. New seals and gaskets installed.
Dana 20 T case rebuilt with new bearings seals and gaskets.
J&B twin stick kit installed on the T case.
Centerforce Dual Friction clutch
Converted over to a hydraulic clutch assembly with new components.
New flywheel
Brakes
Drum brakes in back.
New drums and all new hardware including all new e brake components and wheel cylinders.
Pre bent Stainless brake lines installed with extended Stainless flex lines.
Front brakes converted to power disc.
New master cylinder with new dual diaphragm booster.
1977
Body
A FEW BLEMISHES IN THE PAINT
Body was sandblasted and repairs made that needed done
Underneath and inside tub were sprayed with silver POR 15 then sprayed with gray UPOL Raptor lining.
Rear diamond plate corners installed.
Custom diamond plate rocker covers with side steps
Rear fender wheels with trimmed out larger
Rear TJ flares were installed.
Front Custom tube fenders with custom inner fender wells
Rear tail light guards
Stainless license plate bracket.
All new lights
New window frame, glass and seals.
New mirrors and mounting brackets
Custom roll cage
Turner FX racing seats with 4 point harnesses
Fire extinguishers installed on back of roll cage
Soft top hardware installed
Grant steering wheel
Custom Dash with all Autometer ultra lite gauges with red backlights
All new switches for everything
Rugged Ridge Center Console
Stainless Wiper Arms and Cowl Vent
New Wiper Motor and Linkage Kit
Painless LED turn signal and high beam indicators
Tires & Wheels
37x12.50x15 Super Swamper SSR’s installed on 15x10 American Racing Outlaw II Rims
|
 Vehicle Features: |
 Four Wheel Drive | 8 Cylinder Engine | Power Steering | | Manual Transmission | Doors (Soft) | Locker (Front) | | Locker (Rear) | Locking Hubs | Oversized Tires | | Roll Bars | Side Bars | Soft Top |
|
This classified has expired.
|
|  | |
